Found 10483 publications. Showing page 331 of 420:
Air Quality in Ny-Ålesund. Monitoring of Local Air Quality 2019 and 2020.
The concentrations of the measured components are generally low and below national limit values for the protection of
human health and critical levels for the protection of vegetation. Wind from northern sectors gave the highest average concentrations of nitrogen oxides and sulfur dioxide, which indicates the power station and the harbour as possible sources. We also see single episodes of long-range transport of sulfur dioxide.
NILU
2021
The increased availability of commercially-available low-cost air quality sensors combined with increased interest in their use by citizen scientists, community groups, and professionals is resulting in rapid adoption, despite data quality concerns. We have characterized three out-the-box PM sensor systems under different environmental conditions, using field colocation against reference equipment. The sensor systems integrate Plantower 5003, Sensirion SPS30 and Alphasense OCP-N3 PM sensors. The first two use photometry as a measuring technique, while the third one is an optical particle counter. For the performance evaluation, we co-located 3 units of each manufacturer and compared the results against optical (FIDAS) and gravimetric (KFG) methods for a period of 7 weeks (28 August to 19 October 2020). During the period from 2nd and 5th October, unusually high PM concentrations were observed due to a long-range transport episode. The results show that the highest correlations between the sensor systems and the optical reference are observed for PM1, with coefficients of determination above 0.9, followed by PM2.5. All the sensor units struggle to correctly measure PM10, and the coefficients of determination vary between 0.45 and 0.64. This behavior is also corroborated when using the gravimetric method, where correlations are significantly higher for PM2.5 than for PM10, especially for the sensor systems based on photometry. During the long range transport event the performance of the photometric sensors was heavily affected, and PM10 was largely underestimated. The sensor systems evaluated in this study had good agreement with the reference instrumentation for PM1 and PM2.5; however, they struggled to correctly measure PM10. The sensors also showed a decrease in accuracy when the ambient size distribution was different from the one for which the manufacturer had calibrated the sensor, and during weather conditions with high relative humidity. When interpreting and communicating air quality data measured using low-cost sensor systems, it is important to consider such limitations in order not to risk misinterpretation of the resulting data.
2021
Microfluidic In Vitro Platform for (Nano)Safety and (Nano)Drug Efficiency Screening
Microfluidic technology is a valuable tool for realizing more in vitro models capturing cellular and organ level responses for rapid and animal‐free risk assessment of new chemicals and drugs. Microfluidic cell‐based devices allow high‐throughput screening and flexible automation while lowering costs and reagent consumption due to their miniaturization. There is a growing need for faster and animal‐free approaches for drug development and safety assessment of chemicals (Registration, Evaluation, Authorisation and Restriction of Chemical Substances, REACH). The work presented describes a microfluidic platform for in vivo‐like in vitro cell cultivation. It is equipped with a wafer‐based silicon chip including integrated electrodes and a microcavity. A proof‐of‐concept using different relevant cell models shows its suitability for label‐free assessment of cytotoxic effects. A miniaturized microscope within each module monitors cell morphology and proliferation. Electrodes integrated in the microfluidic channels allow the noninvasive monitoring of barrier integrity followed by a label‐free assessment of cytotoxic effects. Each microfluidic cell cultivation module can be operated individually or be interconnected in a flexible way. The interconnection of the different modules aims at simulation of the whole‐body exposure and response and can contribute to the replacement of animal testing in risk assessment studies in compliance with the 3Rs to replace, reduce, and refine animal experiments.
2021
The Tibetan Plateau (TP), referred to as the “Asian water tower,” contains one of the largest land ice masses on Earth. The local glacier shrinkage and frozen-water storage are strongly affected by variations in surface air temperature over the TP (TPSAT), especially in springtime. This study reveals that the relationship between the February North Atlantic Oscillation (NAO) and March TPSAT is unstable with time and regulated by the phase of the Atlantic multidecadal variability (AMV). The significant out-of-phase connection occurs only during the warm phase of AMV (AMV+). The results show that during the AMV+, the negative phase of the NAO persists from February to March, and is accompanied by a quasi-stationary Rossby wave train trapped along a northward-shifted subtropical westerly jet stream across Eurasia, inducing an anomalous adiabatic descent that warms the TP. However, during the cold phase of the AMV, the negative NAO cannot persist into March. The Rossby wave train propagates along the well-separated polar and subtropical westerly jets, and the NAO–TPSAT connection is broken. Further investigation suggests that the enhanced synoptic eddy and low-frequency flow (SELF) interaction over the North Atlantic in February and March during the AMV+, caused by the southward-shifted storm track, helps maintain the NAO pattern via positive eddy feedback. This study provides a new detailed perspective on the decadal variability of the North Atlantic–TP connection in late winter to early spring.
2021
2021
PM10/PM2.5 comparison exercise in Oslo, Norway. Study in 2015-2016 and 2018.
The purpose of the comparison was to test for equivalence and establish calibration functions for automatic PM-analysers commonly used in Norway. The reference laboratory performed a field test at three different locations in Oslo during summer and winter conditions in the periods September 2015 to July 2016 and February to March 2018. Participating analysers were Palas Fidas 200, Grimm EDM 180, TEI TEOM 1405 DF, TEI FH 62 I-R, and R&P TEOM 1400AB.
The report proposes a system to carry out ongoing verification of equivalence in the Norwegian monitoring network and how to calibrate analyser data.
NILU
2021
Atmospheric corrosion due to amine emissions from carbon capture plants
The atmospheric corrosion due to pure amines emitted from carbon capture plants was investigated. Amine exposure was found to initially inhibit the corrosion of steel, by its film formation and alkalinity, but reduce corrosion product layers and lead to freezing point depression, which could in turn increase the corrosion. Very high amine doses were observed to dissolve the metal without the establishing of a corrosion layer. These effects seem much more pronounced on copper than on steel. Climate and air quality variations affect the steel corrosion much more than the expected maximum amine deposition from carbon capture plant emissions.
2021
Safety assessment of titanium dioxide (E171) as a food additive
The present opinion deals with an updated safety assessment of the food additive titanium dioxide (E 171) based on new relevant scientific evidence considered by the Panel to be reliable, including data obtained with TiO2 nanoparticles (NPs) and data from an extended one-generation reproductive toxicity (EOGRT) study. Less than 50% of constituent particles by number in E 171 have a minimum external dimension < 100 nm. In addition, the Panel noted that constituent particles < 30 nm amounted to less than 1% of particles by number. The Panel therefore considered that studies with TiO2 NPs < 30 nm were of limited relevance to the safety assessment of E 171. The Panel concluded that although gastrointestinal absorption of TiO2 particles is low, they may accumulate in the body. Studies on general and organ toxicity did not indicate adverse effects with either E 171 up to a dose of 1,000 mg/kg body weight (bw) per day or with TiO2 NPs (> 30 nm) up to the highest dose tested of 100 mg/kg bw per day. No effects on reproductive and developmental toxicity were observed up to a dose of 1,000 mg E 171/kg bw per day, the highest dose tested in the EOGRT study. However, observations of potential immunotoxicity and inflammation with E 171 and potential neurotoxicity with TiO2 NPs, together with the potential induction of aberrant crypt foci with E 171, may indicate adverse effects. With respect to genotoxicity, the Panel concluded that TiO2 particles have the potential to induce DNA strand breaks and chromosomal damage, but not gene mutations. No clear correlation was observed between the physico-chemical properties of TiO2 particles and the outcome of either in vitro or in vivo genotoxicity assays. A concern for genotoxicity of TiO2 particles that may be present in E 171 could therefore not be ruled out. Several modes of action for the genotoxicity may operate in parallel and the relative contributions of different molecular mechanisms elicited by TiO2 particles are not known. There was uncertainty as to whether a threshold mode of action could be assumed. In addition, a cut-off value for TiO2 particle size with respect to genotoxicity could not be identified. No appropriately designed study was available to investigate the potential carcinogenic effects of TiO2 NPs. Based on all the evidence available, a concern for genotoxicity could not be ruled out, and given the many uncertainties, the Panel concluded that E 171 can no longer be considered as safe when used as a food additive.
2021
Assessing the impacts of citizen-led policies on emissions, air quality and health
Air pollution is a global challenge, and especially urban areas are particularly affected by acute episodes. Traditional approaches used to mitigate air pollution primarily consider the technical aspects of the problem but not the role of citizen behaviour and day-to-day practices. ClairCity, a Horizon 2020 funded project, created an impact assessment framework considering the role of citizen behaviour to create future scenarios, aiming to improve urban environments and the wellbeing and health of its inhabitants. This framework was applied to six pilot cases: Bristol, Amsterdam, Ljubljana, Sosnowiec, Aveiro Region and Liguria Region, considering three-time horizons: 2025, 2035 and 2050. The scenarios approach includes the Business As Usual (BAU) scenario and a Final Unified Policy Scenarios (FUPS) established by citizens, decision-makers, local planners and stakeholders based on data collected through a citizen and stakeholder co-creation process. Therefore, this paper aims to present the ClairCity outcomes, analysing the quantified impacts of selected measures in terms of emissions, air quality, population exposure, and health. Each case study has established a particular set of measures with different levels of ambition, therefore different levels of success were achieved towards the control and mitigation of their specific air pollution problems. The transport sector was the most addressed by the measures showing substantial improvements for NO2, already with the BAU scenarios, and overall, even better results when applying the citizen-led FUPS scenarios. In some cases, due to a lack of ambition for the residential and commercial sector, the results were not sufficient to fulfil the WHO guidelines. Overall, it was found in all cities that the co-created scenarios would lead to environmental improvements in terms of air quality and citizens’ health compared to the baseline year of 2015. However, in some cases, the health impacts were lower than air quality due to the implementation of the measures not affecting the most densely populated areas. Benefits from the FUPS comparing to the BAU scenario were found to be highest in Amsterdam and Bristol, with further NO2 and PM10 emission reductions around 10%–16% by 2025 and 19%–28% by 2050, compared to BAU.
2021
The 11 year solar cycle UV irradiance effect and its dependency on the Pacific Decadal Oscillation
The stratospheric, tropospheric and surface impacts from the 11 year ultraviolet solar spectral irradiance (SSI) variability have been extensively studied using climate models and observations. Here, we demonstrate using idealized model simulations that the Pacific Decadal Oscillation (PDO), which has been shown to impact the tropospheric and stratospheric circulation from sub-decadal to multi-decadal timescales, strongly modulates the solar-induced atmospheric response. To this end, we use a high-top version of the coupled ocean–atmosphere Norwegian Climate Prediction Model forced by the SSI dataset recommended for Coupled Model Intercomparison Project 6. We perform a 24-member ensemble experiment over the solar cycle 23 in an idealized framework. To assess the PDO modulation of the solar signal, we divide the model data into the two PDO phases, PDO+ and PDO−, for each solar (maximum or minimum) phase. By compositing and combining the four categories, we hence determine the component of the solar signal that is independent of the PDO and the modulation of the solar signal by the PDO, along with the solar signal in each PDO phase. Reciprocally, we determine the PDO effect in each solar phase. Our results show that the intensification of the polar vortex under solar maximum is much stronger in the PDO− phase. This signal is transferred into the troposphere, where we find a correspondingly stronger polar jet and weaker Aleutian Low. We further show that the amplification of the solar signal by the PDO− phase is driven by anomalous meridional advection of solar-induced temperature anomalies over northern North America and the North Pacific, which contributes to a decreased meridional eddy heat flux and hence to a decreased vertical planetary wave flux into the stratosphere.
2021
2021
- Aukra, Harøya, Fræna, Møre & Romsdal fylke, Ormen Lange
- Oljeindustri, prosessanlegg, miljøovervåking
- Luftforurensing, nitrogengjødsling, eutrofiering, forsuring
- Vegetasjon, artssammensetning, nedbørsmyr, kystlynghei
- Plantekjemi, jordanalyser, jordvannanalyser, tungmetaller, gjenanalyserAukra, Harøya, Fræna, Møre & Romsdal county, Ormen Lange
- Oil industry, process plant, environmental monitoring
- Air pollution, nitrogen fertilization, eutrophication, acidification
- Vegetation, species composition, bogs, heathland
- Plant chemistry, soil analyses, ground water analyses, heavy
metals, re-analyses
Norsk institutt for naturforskning (NINA)
2021
Fjernmåling av metanutslipp ved bruk av Sentinel-5P: en mulighetsstudie
Rapporten beskriver hvilke muligheter Sentinel-5P kan gi med tanke på å utvikle produkter for årlige nasjonale dekningskart med arealestimater med vekt på klimagassen metan.
NILU
2021
Monitoring of environmental contaminants in air and precipitation. Annual report 2020.
This report presents environmental monitoring data from 2020 and time-trends for the Norwegian programme for Long-range atmospheric transported contaminants. The results cover 200 organic compounds (regulated and non-regulated), 11 heavy metals, and organic chemicals of potential Arctic concern.
NILU
2021
2021
The influence of probe spacing and probe bias in a double Langmuir probe setup
Multi-needle Langmuir probes are mounted on satellites and sounding rockets for high-frequency characterization of plasma in the ionosphere. Mounted on a spacecraft, the recorded probe current often differs from expected results. In this paper, we perform a numerical study using a particle in cell model to see how the spacing between the individual probes used in a multi-needle setup influences the measured current. We also study how the applied probe bias voltage can contribute to deviations. In our study, we use realistic electron temperatures and electron densities for the relevant part of the ionosphere. However, the results should be generally applicable and valid for other space environments as well as for laboratory Langmuir probe applications. From our study, we can see that when the distance is short, less than two Debye lengths, the current is highly affected, and we can see deviations of more than 60% compared to a single probe setup.
2021
Quantitative chemical analysis of airborne particulate matter (PM) is vital for the understanding of health effects in indoor and outdoor environments, as well as for enforcing EU air quality regulations. Typically, airborne particles are sampled over long time periods on filters, followed by lab-based analysis, e.g., with inductively coupled plasma mass spectrometry (ICP-MS). During the EURAMET EMPIR AEROMET project, cascade impactor aerosol sampling is combined for the first time with on-site total reflection X-ray fluorescence (TXRF) spectroscopy to develop a tool for quantifying particle element compositions within short time intervals and even on-site. This makes variations of aerosol chemistry observable with time resolution only a few hours and with good size resolution in the PM10 range. The study investigates the proof of principles of this methodological approach. Acrylic discs and silicon wafers are shown to be suitable impactor carriers with sufficiently smooth and clean surfaces, and a non-destructive elemental mass concentration measurement with a lower limit of detection around 10 pg/m3 could be achieved. We demonstrate the traceability of field TXRF measurements to a radiometrically calibrated TXRF reference, and the results from both analytical methods correspond satisfactorily.
2021
Calibration of CO, NO2, and O3 Using Airify: A Low-Cost Sensor Cluster for Air Quality Monitoring
During the last decade, extensive research has been carried out on the subject of low-cost sensor platforms for air quality monitoring. A key aspect when deploying such systems is the quality of the measured data. Calibration is especially important to improve the data quality of low-cost air monitoring devices. The measured data quality must comply with regulations issued by national or international authorities in order to be used for regulatory purposes. This work discusses the challenges and methods suitable for calibrating a low-cost sensor platform developed by our group, Airify, that has a unit cost five times less expensive than the state-of-the-art solutions (approximately €1000). The evaluated platform can integrate a wide variety of sensors capable of measuring up to 12 parameters, including the regulatory pollutants defined in the European Directive. In this work, we developed new calibration models (multivariate linear regression and random forest) and evaluated their effectiveness in meeting the data quality objective (DQO) for the following parameters: carbon monoxide (CO), ozone (O3), and nitrogen dioxide (NO2). The experimental results show that the proposed calibration managed an improvement of 12% for the CO and O3 gases and a similar accuracy for the NO2 gas compared to similar state-of-the-art studies. The evaluated parameters had different calibration accuracies due to the non-identical levels of gas concentration at which the sensors were exposed during the model’s training phase. After the calibration algorithms were applied to the evaluated platform, its performance met the DQO criteria despite the overall low price level of the platform.
2021
2021